Highlights:
Made for up to 750°c (1,382°f) for street, some track use and rally use.
Low dust, high performance street pad with 20-25% % brake improvement.
Capable of repeated heavy brake use without brake ?fall-off?.
Very minimal disc/rotor damage characteristics.
Features red ?brake in? Surface coating for instant safe braking after install.
Superb material for European cars.
Ece r 90 type approved for most cars.
High performance lowest dust rating pads for prestige imports and faster street driving.


Redstuff reduce dust by 60-90%. Plus the minimal dust you see is very easily removed with a simple sponge wash as it contains no steel fibre particles as in all other pads. Second they brake like ...(choose a part on the right to read more)

General Fitment

High-quality OEM front chin spoiler kit replacement that includes all necessary installation hardware. We source this part in Germany to ensure quality, reliability and precise fitment. Kit includes: qty. 1 front chin spoiler 930 / 911 wide body / turbo look 1975-89 - 93050305501 qty. 11 spoiler shim - 91150302300 qty. 1 left spoiler mounting plate qty. 1 right spoiler mounting plate qty. 15 m6 stainless nuts qty. 15 m6 washers sold individually. 1 needed per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

If you are experiencing over boost, odds are your wastegate diaphragm is torn or leaking. We are finding more and more failures on these diaphragms with our classics. We strongly recommend replacing them with the addition of an upgraded boost spring, part # FVD123110 . We also recommend replacing the pressure switch, part # 93060610100 high quality, German made, turbocharger wastegate diaphragm membrane. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 4 necessary per car (2 per axle). Please note: this only fits 930 turbo models with the 4 speed transmission # 930.34/36 and the 1984 911 wide body models with the 5 speed transmission # 915.69 and 915.70.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Highlights: made for up to 750*c (1,382*f) for street, some track use and rally use. Low dust, high performance street pad with 20-25% % brake improvement. Capable of repeated heavy brake use without brake "fall-off". Very minimal disc/rotor damage characteristics. Features red "brake in' surface coating for instant safe braking after install. Superb material for European cars. Ece r 90 type approved for most cars. High performance lowest dust rating pads for prestige imports and faster street driving. Redstuff reduce dust by 60-90%. Plus the minimal dust you see is very easily removed with a simple sponge wash as it contains no steel fibre particles as in all other pads. Second they brake like an alligator...(choose a part on the right to read more)

General Fitment

Will ship when available.
930 style upgrade parts for non turbo models.car set includes:
(2) 930 347 031 01
(2) 930 347 191 02
(2) 930 347 313 01
(2) n 011 210 1
(2) 900 021 013 00

The clutch cable disengages the clutch in order to safely shift the transmission. A failing clutch cable can produce the same symptoms as a failing clutch, so we recommend replacing the cable / cables when installing a new clutch. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This part number supersedes part numbers 930 423 401 02 / 03 / 05. Sold individually. 1 necessary per car. Please note: this fits the 1978 930 3.3 l turbo model from chassis # 930 880 0192 on.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check st...(choose a part on the right to read more)

We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)

We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 058 05. We also suggest replacing your outer tie rods, we have a uniball option, our part # 96534703200sp or the OEM style, narrow body is part # 96434703200 or wide body is part # 96434703201 (qty. 2 are needed) and now is also...(choose a part on the right to read more)

We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)

Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)

Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)

The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)

No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)

Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)

A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. Please contact your FVD parts specialist for fitment questions. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Also a now is the time to install a set of our speed bleeders, part # FVD910102. They are comparable to part numbers 993 351 425 10 and 993 351 426 10. Please note: these are aftermarket calipers and do not come with the logo or brake pads. Sold individually. 1 necessary per car.

This item may need to be source...(choose a part on the right to read more)

Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)

Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)

The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)

This is a factory series borg warner / kkk k27 turbocharger. It is a direct replacement for part # 930 123 003 01 which is currently no longer available from the factory. We source this from an OEM supplier with exacting standards in Germany. Features: restore factory performance direct replacement includes turbocharger hose 93011036801eq includes hose clamps sold individually. 1 necessary per car. Please note: there is no applicable core charge on this turbo. We send you a newly remanufactured unit with hose and clamps.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

The moshammer side inlet set is a striking design that enhances performance and efficiency. The inlets create a ram air effect by scooping in a larger volume of air, which delivers up to 10% more air pressure into the intercoolers. These sets are available in satin black, gloss black or high gloss carbon. This is another versatile moshammer offering for a leased vehicle or for those looking to return the car to its original appearance in the future. This set complements the entire moshammer downforce rs (991.1 turbo/s) or evo rs (991.2 turbo/s) aero packages and benefits the mighty GT2 rs as well. Features: striking design increased performance added efficiency direct bolt on available in satin black, gloss bla...(choose a part on the right to read more)

The moshammer front bumper upper air vent is a combination of aggressive styling, aero-efficiency and increased cooling capacity. It is a motorsport finishing touch that complements the entire evo rs (991.2 turbo/s) / stormforce (991.1) / stormforce evo rs (991.2) or downforce rs (991.1 turbo/s) aero packages. FVD Brombacherhas a tradition of offering exclusive body styling that is functional, easily installed, wind tunnel tested, German made and TUV approved. Those high standards naturally led us to the moshammer brand. The moshammer aero styling brand has become a leader in the premium automotive segment. Each part is precision designed and manufactured in Germany for perfect fitment, superior durability and...(choose a part on the right to read more)

The moshammer evo 2 front chin spoiler blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce. Porsche active aerodynamics remains fully functional in all 3 positions and the evo 2 chin spoiler secures seamlessly into the factory locations. The evo 2 spoiler's design offers a more aggressive look but also blends perfectly with other design elements like the side skirts and rear spoiler. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs...(choose a part on the right to read more)

The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the evo rs (991.2 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: vented f...(choose a part on the right to read more)

The moshammer rear wing spoiler lip is a bold, aggressive design that maximizes downforce. The rear spoiler lip installs seamlessly without drilling and the Porsche active rear spoiler remains fully functional. This is the perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs (991.1 turbo/s) packages, the result is a confident, cohesive stance with balanced downforce. Features: aggressive design increased rear downforce improved handling simple to install and remove lightweight composite material designed and manufactured in Germany FVD Brombacherhas a tradition of ...(choose a part on the right to read more)